How to Make a Simple Drawer Plans
How to build Easy DIY Drawer Boxes with lumber. Simple rustic drawer design for storage and other woodworking projects.
Like shooting fish in a barrel DIY Drawer Boxes
Most of the tutorials you find for building drawer boxes are for plywood boxes with a face or for high-cease lumber with fancy joinery.
Merely, sometimes you merely desire an easy, low-cost, uncomplicated drawer box, like this this drawer with a pretty, rustic design.
Here's how I build Like shooting fish in a barrel DIY Drawer Boxes with dimensional lumber.
Some links on this post are chapter links. Equally an Amazon Associate I earn from qualifying purchases at no additional cost to you.
What Tools Do Yous Need?
- Round Saw
- Clamps and Straight Board to brand Straight Cuts
- Wood Glue and Forest Filler
- Brad Nails & Brad Nailer
- Tape Measure out, Pencil, and Carpentry Square
- Power Sander and 120-Grit Sandpaper
Scout the Drawer Box Build Video
If any of the steps for Easy DIY Drawer Boxes are confusing, I highly recommend watching the short video. Hopefully seeing it done can assist clear up any confusion.
How to Make Easy Drawer Boxes for Storage - Simple Design Without a Face
How Much Smaller Should A Drawer Be Than the Opening
The width of your drawer actually depends on the drawer slides you decide to employ. I used depression-cost Euro Slides for this projection. They need a half inch of space on either side to operate properly.
Be certain to read the directions that come with your slides earlier figuring out what size your set up of Easy DIY drawer boxes needs to be.
Quick Notation: If I was edifice drawer boxes for indoor furniture, similar my DIY Farmhouse Console Table, or built-ins; I'd become with nicer soft-close drawer slides.
What Size Should My Drawer Boxes Be?
For this type of drawer, we won't be attaching a face to the drawer box. So, yous desire the width of the forepart and dorsum of the drawer to be the "width of the opening" minus "the space needed for the slides to work".
Then you lot have a total piece of lumber on the front end and the ends of the side pieces won't be showing when the drawer is closed.
When I use plywood, I usually have the elevation of my drawer ane/2″ or iii/4″ below the opening. Only, again, the overall height of your drawer depends on where you mount the slides.
I say, if you lot're new to building drawers and all the math that goes forth with that, install your slides before you lot build the drawer. Then you'll know for sure how much room you have higher up the slide so you can figure out how much clearance you have.
Likewise, I used 1x Dimensional Lumber to build these drawers. A 1x10 was perfect for my drawers. Information technology left me with almost a three/iv″ gap in a higher place the drawer boxes.
If you want your drawers to be unproblematic and quick to build, option a standard size for your opening to avoid cut along the length of the lumber.
Then, if a 1x4 leaves a 1″ or 1 1/2″ gap merely you just want a quick and easy to build drawer box and would rather avert cutting the length of the lath, so become with information technology. It'due south your drawers, after all.
OK, at present that you know how to set the width and height of this Piece of cake DIY Drawer Boxes, allow's get to the build steps.
Steps to Build my Easy DIY Drawer Boxes
Note: I recommend using 1x Common Board, Whiteboard, or Inexpensive Pino to get the same look as my drawers.
These boards look similar, information technology just depends on what region you're in and what is available at that fourth dimension. Information technology's the cheaper, knotty version of 1x in Lowe's or Abode Depot (not the Cedar). Pick the nicest, straightest boards you can find.
You can run into me doing all of these steps in the Easy DIY Drawer Boxes video in a higher place.
- Cut your front and dorsum pieces to the width of the opening minus the drawer slide allowance. I like to utilize a straight board clamped to my boards to get directly cuts with a round saw. Only be sure to adjust your measurement for the distance between the blade on your circular saw and the guide on information technology.
- Cut your two side pieces to the depth you lot want minus the thickness of the forepart and back pieces. Should be i 1/ii″ for Pine or Mutual Board Dimensional Lumber. Sand all 4 pieces with 120-grit sandpaper earlier associates. Be certain to smooth the ends besides. I also like to lightly sand all corners and hard edges for a prettier look. But that'southward optional.
- Assemble the box with wood glue and brad nails. Use a square the keep the boards square. If your drawer boxes aren't foursquare, it might stop your drawer slides from working properly.
- Cut a 1x1 to the length of the inside of the left and right sides of your drawer box. Or, you can rip plywood or lumber to this size with a table saw. Use wood mucilage and brad nails to attach the 2 – 1x1's to the inside bottom edge of the drawer box. These will act equally the supports for the drawer bottom. Of form, in that location are lots of ways to adhere a drawer bottom, but I think this is the easiest fashion to do it. And, we are building Quick and Easy DIY Drawer Boxes, afterwards all. 🙂
- Once the 4 sides and 2 bottom supports are assembled and the gum dries, use wood filler on the nail holes on the front of the drawer box and whatsoever other spots you think need filler, permit that dry then sand once more with 120-grit sandpaper.
- Now, use three/8″ or one/2″ plywood to cut a bottom for your drawer box with your circular saw. I sanded the edges and just dropped mine into place. Just, you could glue and nail it down, if needed.
That'due south it for building these Easy DIY Drawer Boxes. Now, allow's talk nigh how I got that pretty, rustic finish on my drawer boxes.
How I Finished this Simple Drawer Blueprint
Here'due south how I did that pretty whitewash finish on my drawers. I used my DIY Chalk Paint Recipe to make my own chalk paint from Latex Pigment.
All of these steps were done after building my Easy DIY Drawer Boxes, using forest filler anywhere that needed it, and sanding that smooth when it dried. All of this is shown in the video above likewise.
- Apply Danish Oil in Medium Walnut to the entire drawer box, within and out. Follow the directions on the container for the best event.
- Once the Danish Oil dries, use a foam-colored chalk paint to whitewash the drawer fronts. To do this I used a clean, wet rag dipped in chalk paint. Then wiped that across the drawers. The rag needs to be wet to proceed the paint thin. I rinsed my rag and re-wet it subsequently doing 2 drawer fronts. If the rag is too dry, the chalk paint will look more like paint than a whitewash. Wipe off excess chalk paint with a clean, dry rag before it dries.
- Once the whitewash is finished and dries, apply 2 coats of water-based poly over the whitewash. There is no need to poly over the Danish Oil, only you can, if you want to change the sheen or experience of the Danish Oil lonely.
That'southward it for how I whitewashed and protected these Piece of cake DIY Drawer Boxes. What exercise you call back?
Keep scrolling for more than pictures from this DIY.
Looking for more of my Home Comeback Videos? Cheque out this DIY Dwelling Improvement playlist on YouTube.
Tools
- Circular Saw
- Carpentry Square
- Pencil & Tape Mensurate
- Brad Nailer & Nails
Instructions
Steps to Build my Easy DIY Drawer Boxes
Annotation: I recommend using 1x Common Board, Whiteboard, or Inexpensive Pine to go the same look as my drawers. These boards look similar, it just depends on what region yous're in and what is bachelor at that time. Information technology's the cheaper, knotty version of 1x in Lowe's or Home Depot (not the Cedar). Choice the nicest, straightest boards you can find.
Yous can see me doing all of these steps in the Like shooting fish in a barrel DIY Drawer Boxes video.
- Cut your front and dorsum pieces to the width of the opening minus the drawer slide allowance. I like to use a directly board clamped to my boards to get straight cuts with a circular saw. Only be sure to adjust your measurement for the distance between the blade on your circular saw and the guide on it.
- Cut your 2 side pieces to the depth you lot desire minus the thickness of the forepart and dorsum pieces. Should be one ane/two" for Pine or Common Board Dimensional Lumber. Sand all four pieces with 120-grit sandpaper earlier assembly. Exist sure to smooth the ends too. I also like to lightly sand all corners and difficult edges for a prettier look. Just that'south optional.
- Assemble the box with forest glue and brad nails. Utilize a foursquare the keep the boards square. If your drawer boxes aren't square, it might finish your drawer slides from working properly.
- cutting a 1x1 to the length of the within of the left and correct sides of your drawer box. Or, y'all tin can rip plywood or lumber to this size with a table saw. Use wood gum and brad nails to attach the 2 - 1x1'southward to the within bottom edge of the drawer box. These will human activity equally the supports for the drawer bottom. Of course, there are lots of ways to attach a drawer bottom, but I think this is the easiest way to do information technology. And, we are building Quick and Easy DIY Drawer Boxes, after all. 🙂
- One time the 4 sides and two bottom supports are assembled and the glue dries, use wood filler on the nail holes on the front of the drawer box and whatsoever other spots you think need filler, permit that dry out then sand again with 120-grit sandpaper.
- Now, use 3/eight" or i/2" plywood to cutting a bottom for your drawer box with your round saw. I sanded the edges and merely dropped mine into place. Only, you could glue and boom it down, if needed.
That's it for building these Like shooting fish in a barrel DIY Drawer Boxes. Now, let's talk nigh how I got that pretty, rustic finish on my drawer boxes.
Notes
How Much Smaller Should A Drawer Be Than the Opening
The width of your drawer actually depends on the drawer slides you decide to use. I used low-cost Euro Slides for this project. They need a half inch of space on either side to operate properly. Be sure to read the directions that come with your slides earlier figuring out what size your set of Easy DIY drawer boxes needs to exist.
Quick Note, If I was building drawer boxes for indoor piece of furniture, like my DIY Farmhouse Console Table, or built-ins; I'd go with nicer soft-close drawer slides.
What Size Should My Drawer Boxes Be?
For this type of drawer, we won't exist attaching a confront to the drawer box. So, you want the width of the front and back of the drawer to be the "width of the opening" minus "the space needed for the slides to work". Then you lot have a full slice of lumber on the front and the ends of the side pieces won't be showing when the drawer is closed.
When I use plywood, I usually have the height of my drawer i/2" or 3/four" below the opening. Just, again, the overall peak of your drawer depends on where you mountain the slides. I say, if y'all're new to building drawers and all the math that goes along with that, install your slides before you build the drawer. Then you'll know for sure how much room you have higher up the slide so you can effigy out how much clearance y'all have.
Besides, I used 1x Dimensional Lumber to build these drawers. A 1x10 was perfect for my drawers. It left me with most a iii/four" gap above the drawer boxes. If you want your drawers to exist uncomplicated and quick to build, selection a standard size for your opening to avert cut along the length of the lumber.
So, if a 1x4 leaves a 1" or 1 1/2" gap but yous just desire a quick and easy to build drawer box and would rather avoid cutting the length of the board, and then go with information technology. It'southward your drawers, after all. OK, now that you know how to set the width and height of this Easy DIY Drawer Boxes, let's become to the build steps.
How near a bigger woodworking projection? Check out this DIY Laundry Tabular array Over Washer and Dryer. It's a huge improvement in looks and part in a Laundry Room.
And, I love this DIY Modernistic Farmhouse Bench as well.
If you accept an old dresser that needs a new life, hither'southward how to cut a dresser in half to make 2 new pieces of article of furniture.
You might also similar this DIY for How to Whiten Tile Grout. Information technology's a Game Changer!
And, if it is time to Stain your Front Door, check out these steps for how I restain a front door without stripping information technology or removing information technology. 🙂
Feeling inspired? Now that you've read these steps for Easy DIY Drawer Boxes, you can do information technology likewise. Allow me know if y'all have questions.
Don't forget to sign up for the Abbotts At Home email newsletter to get DIY, Remodeling, and Crafty ideas in your inbox.
Source: https://www.abbottsathome.com/easy-diy-drawer-boxes-simple/
0 Response to "How to Make a Simple Drawer Plans"
Post a Comment